tapping temperature
英 [ˈtæpɪŋ ˈtemprətʃə(r)]
美 [ˈtæpɪŋ ˈtemprətʃər]
网络 出炉温度; 出钢温度; 出铁温度
双语例句
- The tapping temperature curve obtained by the mathematical model accords well with the tapping temperature curve obtained by black casket test, so various billet tapping temperature can be forecasted by the mathematical model.
经黑匣子实验验证，该模型计算的出炉温度曲线与黑匣子测试的出炉温度曲线拟合很好，所以可用此模型预测不同钢坯的出炉温度。 - The principle of adjustment of splash slag composition was established by this discussion. The controlling of splash slag quantity, the tapping temperature, the nitrogen pressure and flux, the lance height in splashing slag, and the rate of splashing slag were analyzed too in this.
确立了溅渣调渣原则，对转炉留渣量、出钢温度、氮气压力和流量、溅渣枪位与时间、溅渣率等工艺参数的控制进行了分析。 - If a means of sealing the shell tapping is provided, it shall be suitable for the full pressure/ temperature rating of the valve.
如果提供了用于密封筒形丝锥的工具，这个工序必须适用于阀门所有压力/度等级。 - The refractory consumption rate has been reduced by lowering tapping temperature by about 20 ℃.
转炉出钢温度降低了20℃左右，大大降低了耐火材料消耗； - The results suggest that the corrosion of refractory decreases with CaO/ SiO2 ratio of slag increasing and tapping temperature dropping.
结果表明：渣碱度增加和出钢温度降低都使耐材侵蚀降低。 - The effects of the technical parameters, e.g. tapping temperature, choice of ladle nozzle diameter, flow of melt steel, side dam, strip casting speed, roll pressure, protective gas et, al, on quality of casting strip have been investigated.
同时对出钢温度、钢包水口直径的选择、布流形式、侧封技术、铸带速度、轧制力、保护气氛等工艺参数对铸带质量的影响进行了研究。 - These numerical results coincide with the detected values, which is helpful to laying down the regulation of ladle preheating and the temperature correction during tapping, and optimizing the temperature control during refining.
定量结果的获得，将有助于制定合理的钢包预热制度、出钢温度补正制度，也有助于在LF及VD精炼期间根据不同的钢包状态进行合理的温度控制。 - The appropriate tapping temperature and composition, designed for primary melting GH1040 base metal in arc furnace, provide necessary energy for VOD refining.
设计的初炼炉出钢成分及其出钢温度，为GH1040母材在VOD精炼过程中提供了所需要的热能。 - Results show that the temperature drop in the process of tapping can be dramatically checked by lowering the tapping temperature, minimizing the tapping time and raising the temperature of ladle lining.
研究结果表明，降低出钢温度、缩短出钢时间、提高钢包内衬温度可显著减少出钢过程钢水温降。 - : The metal tapping and slagging protection method and metal temperature keeping protection method as well as their application scope was described.
介绍了连续出铁出渣冲天炉故障时的两种防护方法及其应用范围。